产品展示 | 联系双虎 |

欢迎访问济南双虎围挡厂官网!

经理

13953162123

您先的位置:首页 > 新闻资讯 > 公司新闻

公司新闻

正确安装济南百叶窗的小常识

文章发布: 发表时间:2017-07-18 10:13:16

1、窗框与墙体的衔接

窗框与墙体的固定办法,多见的有衔接件法、直接固定法和假框法三种。
济南百叶窗装置效果图衔接件法:是用一种专门制造的铁件将窗框与墙体相衔接,其长处是对比经济,且基本上能够确保窗的稳定性。衔接件法的做法是先将塑料窗放入窗洞口内,找平对中后用木楔暂时固定。然后,将固定在窗框异型材靠墙一面的锚固铁件用螺钉或胀大螺丝固定在墙上。
Ji'nan shutter device connector renderings: using a specially made iron window frame and the wall will be connected, its advantages are the economic comparison, and basically can ensure the stability of the window. The connecting piece method is first put into the plastic window in the window opening, leveling of temporary fixation with wedge. Then, will be fixed on the window frame profiles against the wall side of the iron anchor with screws or expansion screws on the wall.
直接固定法:在砌筑墙体时先将木砖预埋入窗洞口内,当塑钢窗安入洞口并定位后,用木螺钉直接穿过窗框与预埋木砖衔接,从而将窗框直接固定于墙体上。
Direct fixation: in the first brick masonry wall embedded into the window, when the window into the mouth and an orientation, with wood screws directly through the window frame and the embedded block connection, which will direct the window frame fixed on the wall.
假框法:先在窗洞口内装置一个与塑钢窗框配套的镀锌铁皮金属框,或许当木窗换成塑钢窗时,将本来的木窗框保存,待抹灰装饰完成后,再将窗框直接固定在上述框材上,最后再用盖口条对接缝及边际有些进行装饰。
False box method: first window opening device in a plastic steel window frame and supporting the galvanized sheet metal frame, perhaps when the wooden windows replaced steel windows, the wood window will have to be preserved, plastering decorative finishes, the window frame is directly fixed on the frame, and then cover the mouth of butt joint and marginal some decoration.
2、断定衔接点方位
2, determine the direction of the convergence point
断定衔接点的方位时,首先应考虑能使窗扇通过合页效果于窗框的力,尽可能直接传递给墙体;断定衔接点的数量时,有必要思考避免济南百叶窗在温度应力、风压及其它静荷载效果可能发生的变形;衔接点的方位和数量,还有必要确保在塑钢窗与墙体之间细小的位移,不致影响窗的运用功能及衔接本身。
Determine the connection point range, should first consider the window sash window frame through hinges on the effect of force, directly to the wall as far as possible; that number of connection point, it is necessary to think how to avoid deformation of Ji'nan blinds stress, pressure and other static load effect may occur in the temperature range and the number of connection points; also, the need to ensure that small displacement between the window and the wall, the window does not affect the function and use of cohesion itself.
3、框与墙间缝隙处理
3, the gap between the frame and wall treatment
因为塑料的胀大系数较大,故要求窗框与墙体间应留出必定宽度的缝隙,以习惯塑料弹性变形的安全余量。框与墙间的缝隙,运用泡沫塑料条或油毡卷条填塞,填塞不宜过紧,避免框架变形。窗框附近的表里接缝运用密封资料嵌填紧密。也能够选用硅橡胶嵌缝条,不宜选用嵌填水泥砂浆的做法。
Because the plastic swell coefficient is larger, so the requirements between the window frame and the wall should be set aside by the width of the gap will, the elastic deformation of the plastic used safety margin. The gap between the wall and the frame, the use of foam or rolling packing, packing should not be too tight to avoid deformation of the frame. The table near the window frame using the joint sealing material filling closely. Can also use silicon rubber sealing strip, should not use cement mortar filling approach.
填缝关键两点:榜首,嵌填封缝资料应能接受墙体与框间的相对运动而保持密封功能;第二,嵌填封缝资料不应对塑料窗框有腐蚀、软化效果,沥青类资料可能使塑料软化,故不宜运用。
Key points: first, filling filling sealing material should be able to accept the relative motion between the wall and the frame while maintaining the sealing function; second, filling sealing materials should not plastic window frame corrosion, softening effect of asphalt materials may make the plastic softening, it should not be used.
4、五金配件装置
4, hardware accessories
塑钢窗装置五金配件时,有必要先在杆件上钻孔,然后用自攻螺丝拧入,禁止在杆件上直接捶击钉入。
Plastic windows device hardware accessories, it is necessary to drill holes in the rod, and then use self tapping screws into, is prohibited in the bar directly hammering nails into the.
5、清洗
5, cleaning
窗框扇装置后应暂时取下扇,编号独自保管。窗洞口粉刷时,应将窗表面贴纸维护。粉刷时如框扇沾上水泥浆,应立即用软料抹布擦拭洁净,切勿运用金属工具擦刮。粉刷结束,应及时清除玻璃槽口内的渣灰。
Window frame device should temporarily remove fan numbers alone custody. Window paint, the surface of the window sticker should be maintained. When painting, such as the frame of the fan with cement paste, should immediately wipe with a soft cloth wipe clean, do not use metal tools scratch. Paint the end, should be promptly removed in the notches of the slag glass.